Blog & Resources From the factory floor
How to source, compare, spec and install PPR, PEX and brass systems — written by an ISO 9001 and CE certified manufacturer, producing since 1993, not a content farm. Start with the two pillar guides, then browse by topic and read at your own pace.
I. Start Here Two essential guides
Before you import a container, spec a project or sign a distributor deal, it pays to understand the systems you are selling. If you read only two things before sourcing, read these — who to buy from, and what to sell.
Pillar Guide · Sourcing & Vetting · Live
Where to look, how to tell a real factory from a trading company, which certifications — SGS, CE, ISO — to check, the red flags that should end a conversation, and a reusable sourcing checklist you can apply to any supplier.
Read the sourcing guidePillar Guide · Choosing a System · Live
A B2B comparison across cost, lifespan, temperature, pressure and installation — when PPR wins, why PEX owns underfloor heating, and how brass ties the system together — so you stock what your market actually buys.
Read the comparison guideNew to sourcing? Start with the sourcing guide
II. The Library Browse by topic
Guides are grouped under the topics that matter most to importers, distributors, projects and installers — PPR systems, underfloor heating, brass and valves, sourcing and import, and the standards behind them. New guides publish on a rolling schedule.
Underfloor Heating · 16 Apr 2026
Yes, but only in three narrow cases. A decision table by configuration, the loop length and floor area one circuit can cover, and the four functions you lose without a manifold.
Read the guideUnderfloor Heating · 15 Apr 2026
What to fix before you send a manifold RFQ into the Gulf: a 15-line specification table, the G / R / Rp / NPT thread codes, and which conformity scheme each Gulf state runs.
Read the guideUnderfloor Heating · 10 Apr 2026
The mixing valve setting is a calculation, not a preference: flow temperature bands by floor build-up, the EN 1264 / ISO 11855 surface limits that cap every setting, and the ISO 10508 pipe class.
Read the guideUnderfloor Heating · 9 Apr 2026
Pitch sets the output, loop length sets the flow. Spacing by room type, loop length by pipe diameter, area per loop worked from the pitch arithmetic, the pipe take-off and six errors that surface after the screed.
Read the guideUnderfloor Heating · 7 Apr 2026
A wiring centre reconciles thermostats, actuator heads, the pump and the heat source at the manifold. A full terminal schedule, the channel-versus-loop counting problem, and the six wiring faults behind most commissioning callbacks.
Read the guideUnderfloor Heating · 4 Apr 2026
A thermostat is chosen by switching voltage, output type, sensor configuration and back-box fit — not by its display. The selection table, why actuator starting current welds contacts, and the floor surface-temperature limits that set the probe.
Read the guideUnderfloor Heating · 30 Mar 2026
Which manifold body belongs in your warehouse? Stainless steel and brass compared on corrosion, accessory fit and landed cost — plus the alloy designations to name in a purchase order and why CW617N is not a low-lead grade.
Read the guideUnderfloor Heating · 26 Mar 2026
Pressure test, flush, balance, prove the controls, then ramp the screed: six commissioning stages in fixed order, each with a typical hold-point band and the record you hand over.
Read the guideUnderfloor Heating · 24 Mar 2026
A boiler runs hot, a screed floor does not. How manifold pump and mixing units reconcile the two: thermostatic vs motorised control, pump sizing, and what decides fit.
Read the guideUnderfloor Heating · 24 Mar 2026
The cabinet is sized by the assembly inside it, not by the wall. One width rule (manifold width plus ~200 mm), why a 100 mm stud will not take an actuator-fitted manifold, and the placement rules that keep the wall shut.
Read the guideUnderfloor Heating · 20 Mar 2026
Ports, loops and control zones are three different counts, and only one sizes the manifold. A port-count table by dwelling type, loop-length limits, and when to split manifolds.
Read the guideUnderfloor Heating · 18 Mar 2026
Choosing an underfloor heating manifold actuator is four decisions: voltage, normally-closed or normally-open action, valve thread and wiring-centre load. A ten-row selection table with typical stroke and closing force, plus the faults each mismatch causes.
Read the guideIII. E-E-A-T From the factory, not a content farm
Most piping content online is written to rank, not to inform — thin listicles from marketplaces and content farms that have never welded a joint or shipped a container. Our guides come from a working factory floor.
PPR, PEX and brass systems plus underfloor heating, manufacturing since 1993 on our own extrusion, injection-moulding and machining lines — one complete system from one source, mixed in a single container. The standards you read here are the ones our own importers and project buyers hold us to.
ISO 9001:2015, ISO 14001:2015 and ISO 45001:2018 management systems, plus EU CE, Swiss SGS and Russian PT marks — third-party certifications you can verify in the issuing bodies’ own registers rather than take on trust. They are what decide tenders and market entry across Europe, Asia, Africa and beyond. Certificate numbers are available on request.
Every guide answers something our own importers, projects and private-label partners actually ask us. When a guide tells you how to spot a real factory, it is not theory — it is how we operate.
IV. Subscribe Stay updated
We publish practical, manufacturer-written guides for importers, distributors, projects and installers — from PPR welding and manifold installation to certification and importing. Subscribe and we’ll send each new guide as it goes live. No spam; unsubscribe anytime.
We publish sourcing, comparison, certification and installation guides written by the technical team. Tell us which systems you work with and we will send new guides as they go live — and answer any technical question you have in the meantime.
Ask the technical teamV. FAQ Common questions
Start Here Let’s talk
One manufacturer behind every guide — PPR, PEX, brass and underfloor heating from our own production lines, since 1993. Response time: within one working day.
